Die Casting ResourceTechnical guides for die casting buyers, spec writers, and plant managers.
Secondary Operations

How to Specify Tolerances for Machined Die Casts

Published 11 min read

A machined aluminum die casting part resting on a metal inspection table with a micrometer nearby
Quick answer

Specify tolerances by defining the casting baseline, mapping machining allowances, and setting surface finish requirements. Use clear GD&T notation and verify with inspection plans. This guide helps buyers write RFQs for machined die casting that meet strict dimensional and surface standards.

Key takeaways
  • Define the as-cast dimensions before specifying machined tolerances to avoid over-machining or under-machining.
  • Use GD&T where possible to reduce ambiguity in hole position, flatness, and perpendicularity calls.
  • Specify surface finish in micro-inches or microns and confirm whether it applies to machined, cast, or both surfaces.
  • Include a material and heat treatment condition in the drawing to ensure consistent machining behavior.
  • Verify the specification with a sample or first article inspection before releasing the production order.

Start With the As-Cast Geometry

A tolerance specification for a machined die cast part only works if it references the correct starting point. The as-cast geometry is the baseline from which material is removed. If the specification assumes a perfect casting, the machining operation becomes unpredictable. If the casting tolerance is too loose, the machinist must remove more material, which can affect strength or weight. If the casting tolerance is too tight, the machining allowance may be insufficient.

Review the die casting drawing first. Note the critical dimensions that define the part shape. Then identify which of those dimensions will be machined. This step separates the casting requirements from the machining requirements. It also helps the supplier understand where the process control shifts from the die to the CNC machine. For example, consider a hydraulic pump housing made from A380 aluminum. The external housing dimensions might be controlled by the die with a tolerance of plus or minus 0.2 mm. However, the internal bore where the piston will slide is machined to a precision of 0.05 mm. If the buyer specifies only the final bore diameter without accounting for the as-cast condition, the supplier might cast the bore too small, leaving no material for the cutting tool to remove. Conversely, if the casting is too large, the part becomes heavier and the wall thickness becomes uneven after machining.

The as-cast geometry also dictates the location of the parting line and the sprue. These features are permanent marks on the surface. They must be excluded from critical surface finish requirements or positioned so they do not interfere with functional areas. If a gasket face is machined, it should ideally be located away from the parting line. If it is not, the specification must account for the texture left by the die. This requires a different machining depth or a different surface finish expectation.

Map the Machining Allowance

The machining allowance is the thickness of material removed after casting. A typical allowance for precision die casting is between 0.5 and 1.5 millimeters on machined surfaces, depending on the material and the complexity of the shape. For complex parts with thin walls or deep pockets, the allowance may need to be larger. For simple flat plates, it may be smaller.

Specify the allowance explicitly on the drawing. Do not assume the supplier will know how much material to leave. Write the allowance in the general notes or on the dimension itself. For example, if a face is to be machined, note “0.75 mm allowance on all machined faces.” This prevents the casting from being too thin before machining. In practice, a machinist needs enough material to cut through any die marks, flash, or surface imperfections. If the allowance is 0.5 mm and the die leaves a 0.4 mm bump, only 0.1 mm remains for the actual machining cut. This leaves little room for tool deflection or wear. A 1.0 mm allowance provides a safer buffer.

Consider the machine capability. A standard three-axis mill might struggle with deep pockets if the allowance is excessive. The tool must reach the bottom of the pocket without chipping or breaking. For a deep bore, the allowance must allow for the drill or reamer to clear the casting. If the casting is out of alignment with the machine table, the tool may hit the opposite wall. A generous allowance protects the tool and the part. However, excessive allowance increases machining time and cost. It also increases the weight of the raw casting, which affects shipping and handling. Balance the allowance based on the part’s complexity. For a simple flange, 0.5 mm may be sufficient. For a complex manifold, 1.5 mm or more might be necessary.

Assign Tolerances by Feature Type

Different features require different tolerance strategies. A machined face usually calls for flatness and perpendicularity. A machined bore or plug hole calls for diameter and position. A machined thread calls for pitch and depth. Do not apply a single tolerance class to the entire part. That approach either wastes money on over-tight tolerances or risks rework on critical features.

Use the table below as a starting framework. Adjust the values based on the function of the part. A bearing seat requires tighter tolerances than a mounting flat. A sealing surface requires better surface finish than a non-critical mating surface.

Feature Type Typical Tolerance Range Typical Surface Finish
Machined Flat 0.05 mm to 0.10 mm 1.6 to 3.2 microns
Bore or Plug Hole 0.05 mm to 0.15 mm 1.6 to 3.2 microns
Threaded Feature 0.10 mm to 0.20 mm 3.2 to 6.3 microns
Profile Surface 0.10 mm to 0.25 mm 3.2 to 6.3 microns
Non-Critical Machined Face 0.15 mm to 0.30 mm 6.3 to 12.7 microns

For instance, a mounting flat on an engine block does not need to be perfectly flat to 0.05 mm. It only needs to be flat enough to distribute the load of the bolts. A tolerance of 0.15 mm might be acceptable. However, the surface where a hydraulic seal sits requires a much tighter flatness and a smoother finish to prevent leaks. If you specify 0.15 mm for the seal surface, the part will leak. If you specify 0.05 mm for the mounting flat, you pay extra for machining time that provides no functional benefit.

Threads are another area where specific attention is needed. The pitch and depth determine the fit. A thread that is too shallow will not engage fully. A thread that is too deep will strip the mating part. The tolerance range in the table covers the general case, but the specific thread standard, such as metric or imperial, must be stated. The thread class also matters. A fine pitch thread for a sensor housing requires tighter control than a coarse pitch thread for a cover bolt.

Control Position With GD&T

General Tolerance Dimensions reduce ambiguity in assembly. A simple “plus or minus” tolerance on a hole position can lead to misalignment if the hole is drilled from multiple directions. GD&T defines the relationship between features. It also allows the part to be inspected without needing to reference the entire part geometry.

For example, use a position call with a true position symbol for a group of holes that must align with a mating part. Use a flatness call for a face that must seat against a gasket or another plate. Use a perpendicularity call for a surface that must be square to a datum. If the part has multiple machined features, define three datums. These datums should be selected from features that are easy to inspect and that control the part’s orientation in the assembly.

GD&T is particularly useful for parts with multiple holes. Imagine a gearbox housing with four shaft bores. If each bore is specified as “plus or minus 0.05 mm” from the center of the casting, the bores might be individually within tolerance but misaligned relative to each other. The shafts would not mesh. Using a position tolerance with a datum reference ensures that the bores maintain the correct relationship to each other. The datum might be a machined face and a specific bore. This locks the part in the inspection fixture. The position tolerance then controls the hole position relative to that locked orientation.

Selecting the right datums is critical. The datums should be stable and easy to measure. A large flat face is a good primary datum. A cylindrical bore is a good secondary datum. A second flat face or a specific hole location is a good tertiary datum. Avoid using features that are difficult to access or that are not machined. If a datum is a rough casting surface, it will not hold the part consistently in the inspection setup. Use machined features for datums whenever possible.

Specify Surface Finish and Material Condition

Surface finish affects friction, wear, and appearance. For die casting machining, specify the finish in micro-inches or microns. Clarify whether the finish applies to all machined surfaces or only specific features. A finish of 1.6 microns is smooth and often used for sealing or sliding surfaces. A finish of 12.7 microns is acceptable for non-critical machined areas.

The material condition matters as well. Aluminum die castings are often used in the as-cast condition. Magnesium die castings may require heat treatment. Steel die castings are less common but may require annealing. State the material condition in the drawing. If the part requires a specific heat treatment, define it before or after machining. Heat treatment after machining can relieve stress but may require final machining.

For aluminum, the as-cast condition is usually sufficient for most machined parts. However, if the part is subjected to high vibration or impact, a stress relief heat treatment before machining can improve dimensional stability. After heat treatment, the metal may move slightly. This requires a final machining pass to bring the critical dimensions into tolerance. If you specify a heat treatment but do not account for the movement, the part may be out of tolerance after the final cut. State the sequence clearly. For example: “Heat treat in T6 condition. Machine to final dimensions after heat treatment.”

For magnesium, heat treatment is often required to improve corrosion resistance and machinability. The drawing must specify the condition, such as T5 or T6. Failure to specify this can lead to parts that are too soft or too hard. Steel die castings are less common in general machinery but are used in heavy equipment. They often require annealing to reduce hardness and improve machinability. If the steel is too hard, the cutting tools wear quickly and the surface finish degrades. Specify the annealing requirement in the material notes.

Verify With a Sample Inspection Plan

The final step is verification. Before releasing the production order, request a first article inspection. The inspection plan should reference the drawing and the specific features that are critical to function. Include dimensions, surface finish, and material condition.

Ask the supplier to provide a CMM report or a manual measurement report. For critical parts, include a witness point inspection. This ensures that both parties agree on the interpretation of the specification. If the first article fails, the drawing or process needs correction. This step prevents costly rework during production.

A first article inspection is not just a formality. It is a process check. The supplier uses it to verify that their tooling, program, and material are correct. If the first part fails, the supplier can adjust the process before producing the full quantity. If you skip this step and order 1000 units, and the first 50 are rejected, you have lost time and money.

The inspection plan should be specific. Do not just say “inspect the part.” List the specific features to be measured. For example: “Measure bore diameter at three points. Measure flatness of the top face. Measure surface finish on the sealing surface. Verify material condition by spectrographic analysis.” This removes ambiguity. The supplier knows exactly what to report. You know exactly what to accept. If a feature is not on the list, it is not inspected. This can lead to surprises in production.

Common Mistakes to Avoid

Buyers frequently make errors that lead to rejected parts. The most common mistake is specifying a tolerance without a datum. A hole position without a datum reference is ambiguous. Another mistake is assuming the supplier will understand the machining allowance. If the drawing does not state the allowance, the supplier may use a default value that does not fit the part.

Surface finish is another frequent issue. A general note of “3.2 microns finish” without specifying which surfaces apply can lead to disputes. State which surfaces are included. Also, do not mix metric and inch units on the same drawing. Choose one system and stick to it.

Other common mistakes include vague material specifications. Writing “aluminum” instead of “A380” or “A356” allows the supplier to use a cheaper alloy that may not meet the strength or corrosion requirements. Similarly, writing “machined” without specifying the method or finish can lead to inconsistent results. Specify the process if it is critical. For example, “milled” rather than just “machined” clarifies the expected surface texture and tool path.

Another mistake is ignoring the as-cast condition. If the drawing shows a perfect part without accounting for the casting defects, the supplier cannot produce it. Always include the as-cast tolerance and the machining allowance. This aligns the casting and machining processes. It also allows the supplier to identify potential issues early in the design review.

Final Verification

After the first article is approved, confirm the production setup. The supplier should use the same tooling, material, and process parameters. Keep the approved sample or reference part on file. If the part design changes, update the tolerance specification before releasing the new order. A clear, well-structured specification reduces communication gaps and improves yield.

Keep the approved sample in a controlled environment. Temperature and humidity can affect metal dimensions. Store the sample in the same conditions as the production parts. If you need to re-inspect a part in the future, you have a reference point. If the drawing changes, even slightly, the entire specification must be updated. A change in one dimension can affect the machining allowance and the GD&T datums. Review the entire drawing for consistency. A small change can have a large impact on the manufacturing process.

How to Write Clear RFQ Specifications

When writing the RFQ, include the drawing, the material specification, the quantity, and the inspection requirements. State the expected lead time and the delivery terms. If the part is for a regulated industry, include the relevant compliance requirements. The RFQ should be self-contained. The supplier should not need to ask basic questions. A clear RFQ reduces the time to quote and improves the accuracy of the estimate.

The RFQ is the first point of contact. It sets the tone for the relationship. If the RFQ is vague, the quote will be vague. If the drawing is missing, the supplier will have to guess the material and finish. This leads to a low ball quote that may not be achievable. Include all relevant documents. Attach the drawing, the material certificate requirements, and the inspection plan. State the quantity and the delivery date. If the part is for an automotive or medical application, state the required certifications, such as ISO 9001 or IATF 16949. This filters out suppliers who do not meet the quality standards.

Conclusion

Specifying tolerances for machined die casting parts requires precision and clarity. Start with the as-cast geometry. Map the machining allowance. Assign tolerances by feature type. Use GD&T where appropriate. Specify surface finish and material condition. Verify with a sample inspection plan. Avoid common mistakes like missing datums or ambiguous finish notes. A well-written specification ensures the part meets its functional requirements and reduces the risk of rework.

Frequently asked questions

What is the typical machining allowance for aluminum die castings?

A typical allowance for precision die casting is between 0.5 and 1.5 millimeters on machined surfaces. The exact value depends on the part complexity and material.

Should I use GD&T or simple plus or minus tolerances?

Use GD&T for features that control position, orientation, or form relative to other features. Use simple plus or minus tolerances for independent dimensions where the relationship to other features is not critical.

How do I specify surface finish on a drawing?

Use the surface finish symbol and state the value in microns or micro-inches. Specify which surfaces the finish applies to. Do not use a general note that applies to the entire part unless all surfaces are identical.

What happens if the as-cast tolerance is too loose?

The machinist must remove more material to achieve the specified dimension. This can reduce wall thickness, increase weight, or lead to scrap if the material is too thin.

Do I need to specify heat treatment for die cast parts?

Yes, if the part requires a specific material condition. State whether the heat treatment is before or after machining. This ensures the supplier follows the correct process.