Die Casting ResourceTechnical guides for die casting buyers, spec writers, and plant managers.
Aluminum Die Casting

Checklist: Verifying Aluminum Alloy Certificates

Published 7 min read

A printed aluminum alloy certificate with heat number visible
Quick answer

Buyers can verify supplier documentation by checking heat numbers, mill certifications, chemistry ranges, and traceability links. This checklist helps confirm alloy compliance, reduce rejection risk, and maintain a clear audit trail for aluminum parts.

Key takeaways
  • Match heat numbers on certificates to part labels, purchase orders, and shipping documents.
  • Verify chemistry values fall within the specified alloy range, not just the nearest nominal value.
  • Look for a clear chain of custody from mill to foundry to your receiving area.
  • Flag missing signatures, expired certificates, or mismatched lot sizes as immediate issues.

Why alloy certificates matter for die casting buyers

Aluminum alloy certificates are the paper trail that connects a finished casting to its raw material source. Without them, you cannot prove the heat lot, the chemistry, or the processing history of the material. For buyers, this documentation protects you from receiving off-spec alloy, from disputes with suppliers, and from failures in downstream processes.

A missing or incorrect certificate can delay a production line, trigger rework, or force a partial scrap of a finished lot. The cost is not just material. It includes re-inspection, re-heat-treatment, re-machining, and customer notification. A quick verification routine before acceptance prevents these downstream costs.

What to check in a supplier’s alloy certificate

Start with the document itself. A valid aluminum alloy certificate should name the supplier, the customer, the alloy designation, the heat number, and the quantity of material covered. It should also include the test method used, the date of issue, and a signature or digital approval from the issuing authority.

Do not accept a certificate that lists only a generic alloy name without a heat number. A heat number is the unique identifier for a batch of molten aluminum that was melted, tested, and shipped together. If the heat number is missing, the certificate is not a traceability document. It is a statement of intent.

Look for the chemistry section. It should list the major and minor elements, usually as weight percentages. The values should be specific, not ranges. If a certificate says “Al 90-99,” that is not a test result. It is a specification. A test result should say “Al 98.5” or similar, depending on the alloy and the test method.

How to match heat numbers across your documents

The heat number must appear in three places: the supplier’s certificate, the packing list or bill of lading, and the label on the ingot or die-casting bar. If any of these three documents show different heat numbers, stop. Do not accept the material until the discrepancy is resolved.

A common mistake is accepting a heat number from the purchase order. The purchase order may list a requested heat, but the supplier may ship a different one. The certificate must show the actual heat that was tested and delivered. If the purchase order and the certificate do not match, the supplier has not documented the material they actually shipped.

Keep a log of heat numbers. Even if you receive material monthly, track each heat in a simple spreadsheet or your quality system. This log becomes your audit trail. If a problem appears in production, you can quickly isolate the affected heat and contact the supplier with the exact heat number.

Chemistry verification and alloy designation

The alloy designation on the certificate should match the one in your purchase order. For example, if you ordered 356, the certificate should say 356. Do not accept a certificate that says “Aluminum alloy, close to 356” or “356 equivalent.” The designation must be exact.

Check the element values against the alloy specification. For 356, silicon is the primary alloying element. Magnesium, manganese, and iron are minor elements. The values should fall within the acceptable range for the grade. If a value is slightly out of range, ask the supplier for clarification. Do not assume it is acceptable.

A red flag is a chemistry table that looks too clean. If every value is a round number, or if the sum of the elements does not add up to roughly 100 percent, the data may be estimated rather than measured. A real test result will have slight variation. A real chemistry table will have values that add up correctly within a small tolerance.

Traceability from mill to foundry to your plant

A complete traceability chain includes the mill that produced the raw aluminum, the foundry that cast the die-casting, and your receiving area. The certificate should show the mill name or a reference to the mill’s own test report. It should also show the foundry’s name, the die-casting process used, and the date of casting.

If the certificate only shows the foundry name and not the mill, ask for the mill’s test report. The foundry may have melted multiple mill heats into a single die-casting batch. In that case, the certificate should list all contributing heat numbers. If it lists only one heat number, confirm that the entire batch came from that single heat.

A missing mill reference is a red flag. It means the supplier cannot prove the origin of the raw material. Without a mill reference, you cannot verify the source of the aluminum. This is especially problematic for alloys where impurities from the mill can affect casting quality.

Red flags that should trigger a hold

Hold the material if the certificate is unsigned, unsigned, or has a date in the future. A certificate with a date after the ship date is invalid. A certificate with no signature is a draft, not an approved document. Both are reasons to stop acceptance.

Hold the material if the quantity on the certificate does not match the quantity delivered. If the certificate says 500 kg and you receive 450 kg, the discrepancy must be resolved before the material enters production. A quantity mismatch can indicate that the heat number was reused, that material was substituted, or that the certificate was generated incorrectly.

Hold the material if the certificate is a photocopy without a verification code. Some mills and foundries use digital certificates with a verification link or code. If you receive a plain photocopy with no way to verify authenticity, request the original or a digitally signed version. Do not accept a photocopy as the sole record of traceability.

Check Item What to Verify Red Flag
Heat Number Present on certificate, packing list, and ingot label Missing or mismatched heat numbers
Alloy Designation Matches purchase order exactly “Equivalent” or “close to” language
Chemistry Values Specific test results, not ranges Round numbers or sum not near 100%
Date of Issue Before or on the ship date Future date or no date
Quantity Matches delivered weight Quantity mismatch with receiving report
Mill Reference Mill name or report included No mill name or source
Signature Signed or digitally approved by issuer Unsigned or draft status

How to build a quick verification routine

Create a one-page checklist for your receiving team. The checklist should be laminated or printed and placed at the receiving dock. Each receiving inspector should check the items in order before signing for the material. The checklist should take no more than five minutes. If it takes longer, the process is too complicated.

The first step is to confirm the heat number appears on three documents. The second step is to match the alloy designation to the purchase order. The third step is to check the chemistry table for specific values. The fourth step is to verify the date, quantity, and signature. The fifth step is to log the heat number in your quality system.

Train your receiving staff on the red flags. They do not need to be metallurgists. They need to recognize a missing heat number, a future date, or a quantity mismatch. If they see any of these, they should stop the receiving process and call the quality manager. Do not let the material move to the warehouse while the issue is unresolved.

What to do when a certificate fails verification

If a certificate fails, do not accept the material. Do not let it sit in the warehouse with a “pending” tag. Move it to a quarantine area with a red tag that states the reason for hold. Contact the supplier immediately. Provide the specific failure: the missing heat number, the future date, the quantity mismatch, or the missing mill reference.

Ask the supplier to provide a corrected certificate. If they cannot provide one, return the material or request a replacement with a valid certificate. Keep a record of the communication. This record protects you if the material later causes a quality issue. It shows you did not accept non-compliant documentation.

If the supplier frequently sends incorrect certificates, escalate the issue. A pattern of documentation errors suggests a weak internal process at the supplier. You may need to require a pre-shipment certificate review, or you may need to switch suppliers. A supplier that cannot provide accurate documentation cannot be trusted with traceability.

How to store certificates for audit purposes

Store certificates in a way that links them to the material. If you receive aluminum in ingots, store the certificate in a folder with the heat number on the tab. If you receive die-castings, store the certificate in the lot record. The certificate should be retrievable within minutes, not days.

Use a digital archive if possible. Scan the certificate and store it in your quality management system. Link the file to the purchase order and the heat number. This makes it easy to search by heat number, supplier, or date. A digital archive also reduces the risk of a lost paper document.

Keep certificates for the lifespan of the part. If the aluminum parts are used in automotive or structural applications, the retention period may be longer. Check your customer requirements and your internal quality policy. A certificate that is discarded before the part is installed can cause a failure to be untraceable.

Frequently asked questions

Can I use a supplier's general alloy specification instead of a heat-specific certificate?

No. A general specification tells you what the alloy should be. A heat-specific certificate tells you what this particular batch actually was. You need the heat-specific certificate for traceability.

What if the heat number on the ingot label is scratched off?

Do not accept the material. The label is part of the traceability chain. If it is damaged, the supplier must provide a replacement label or a verified heat number from their records.

How do I verify a digital certificate without access to the supplier's portal?

Ask the supplier for the verification code or link. If they cannot provide it, request a signed PDF with a digital signature or a paper original. Do not accept a PDF without a way to verify authenticity.

Is a certificate from a subcontracted foundry acceptable?

Yes, if it includes the mill reference and the full traceability chain. The foundry's certificate should show the raw material source, the casting process, and the final test results.

How long should I keep alloy certificates?

Keep them for the useful life of the part plus any customer-required retention period. For most industrial aluminum parts, keep them for at least five years. Check your customer contracts for specific requirements.