Die Casting ResourceTechnical guides for die casting buyers, spec writers, and plant managers.
Zinc & Magnesium Alloys

Checklist: Verifying Zinc and Magnesium Alloy Certificates

Published 9 min read

Close up of a signed alloy certificate with heat number visible
Quick answer

Verify alloy certificates for zinc and magnesium die castings by checking heat numbers, chemical analysis, mill test reports, and traceability records. This practical audit checklist helps buyers confirm incoming parts meet specified composition and quality standards before acceptance.

Key takeaways
  • Cross-check heat numbers on alloy certificates against material certificates and part markings before releasing inventory.
  • Verify chemical analysis values fall within the specified alloy range, not just the general alloy family.
  • Confirm mill test reports and heat analysis documents carry signatures or digital validation from the foundry or mill.
  • Keep traceability records linked to each lot so nonconforming material can be isolated quickly.
  • Watch for missing heat numbers, generic descriptions, or unsigned documents that break the supply chain audit trail.

Why alloy certificates matter for zinc and magnesium parts

Zinc and magnesium die castings look identical in many production environments. A bracket, housing, or connector may arrive with the same surface finish and dimensional tolerance, yet the underlying chemistry differs. A zinc part intended for general service may contain a different zinc, aluminum, copper, and iron balance than a magnesium part meant for structural use. Without a proper certificate, a buyer cannot prove the material meets the drawing requirement.

Alloy certificates serve as the paper trail that ties a physical part back to the specific heat of metal used. For zinc die casting, this usually means verifying the composition of the melt or ingot. For magnesium alloy, the check is similar but often more sensitive, because magnesium alloys have tighter chemistry windows and are more reactive. When certificates are missing, vague, or inconsistent, the risk moves from a paperwork gap to a potential failure in service.

This checklist is built for receiving inspections and supplier quality reviews. It assumes the buyer has access to mill test reports, heat analysis documents, and part markings. Each item is a verification step that can be completed during a receiving audit or a supplier scorecard review.

Verify heat numbers and traceability

The first check is whether every document references the same heat number or lot identifier. A heat number is the unique code assigned to a specific batch of metal melted or ingoted. For zinc, this may trace back to the ingot supplier or the foundry melt log. For magnesium, it often traces to the extrusion or ingot supplier, and sometimes to the secondary processing step.

  • Match the heat number on the alloy certificate to the heat number on the mill test report.
  • Check that the heat number appears on the part marking, if required by the drawing.
  • Confirm the heat number is not a generic code like “LOT1” or “ZINC” without a unique identifier.
  • Verify the date on the document matches the expected production window for the part.

A common red flag is a heat number that changes from one document to another. This can happen when a foundry blends multiple heats to meet a large order, but the paperwork does not reflect the blend. If the blend is not declared, the buyer cannot trace a defect back to a single heat.

Another red flag is a missing heat number on the part itself. Some magnesium castings are not marked because the parts are used in applications where marking is not practical. In those cases, the buyer must rely on lot-level traceability in the receiving report. Without a part marking, the traceability chain is weaker.

Confirm chemical analysis values

The chemical analysis is the core of the certificate. It lists the elemental composition of the alloy. For zinc, the main elements are zinc, aluminum, copper, and iron. For magnesium, the key elements are magnesium, manganese, nickel, and sometimes silicon or iron. The certificate should show measured values, not just the nominal alloy specification.

A typical zinc alloy may be specified by a standard alloy designation. The certificate should show the actual measured percentages for each element. A typical magnesium alloy, such as a structural grade, will have a tighter range for manganese and nickel. If the measured value falls outside the specified range, the part should be held for review.

Element Typical Check for Zinc Typical Check for Magnesium
Base metal Verify zinc content is within the specified alloy range Verify magnesium content is within the specified alloy range
Aluminum Check aluminum level against the drawing specification Check aluminum level if it is a controlled element in the alloy
Copper Verify copper is within the specified range for the alloy grade Not a primary element, but check if specified for corrosion resistance
Iron Verify iron is within the specified range for the alloy grade Check iron level, which can affect corrosion resistance
Manganese Usually not a controlled element in zinc alloys Verify manganese is within the specified range for the alloy grade
Nickel Not a primary element in most zinc alloys Verify nickel is within the specified range for the alloy grade

Red flags include a certificate that lists only the alloy name without measured values. For example, a document that says “Zinc A” without showing the actual zinc, aluminum, copper, and iron percentages is not a true alloy certificate. It is a label. A second red flag is a measured value that is slightly outside the range. A value of 0.5 percent iron in a zinc alloy that specifies a maximum of 0.4 percent is a small deviation, but it may indicate a process issue that could repeat in the next lot.

For magnesium, the tolerance is often tighter. A deviation in manganese or nickel can change the mechanical properties and corrosion behavior. If the certificate shows a value outside the specified range, do not release the part. Contact the foundry and request a retest or a corrected heat analysis.

Check document signatures and mill approval

A valid alloy certificate is not just a list of numbers. It is a statement made by a responsible party. For zinc die casting, this may be the foundry that produced the castings or the ingot supplier. For magnesium, it may be the extrusion mill or the foundry, depending on where the alloy was produced. The certificate should carry a signature, a stamp, or a digital validation method that ties it to a real person or company.

  • Look for a printed or handwritten signature from the quality representative.
  • Check for a company stamp or seal that matches the supplier’s letterhead.
  • Verify the name and title of the person signing the document.
  • Confirm the date of issuance is before the date of shipment.

A red flag is a certificate with no signature. In some electronic systems, a digital signature or an authenticated PDF may replace a wet ink signature. If the buyer requires a wet ink signature, state that requirement in the purchase order. If the supplier only provides electronic documents, confirm that the digital validation method is acceptable.

Another red flag is a certificate that is on generic stationery without a company name. This is not uncommon with small suppliers, but it weakens the audit trail. If the certificate is on a plain sheet of paper with no company logo or address, request a corrected document on official letterhead. The certificate should be traceable to the supplier, not just to a generic document.

Verify the certificate matches the drawing and specification

The alloy certificate must align with the drawing specification. The drawing will list the alloy grade, such as a zinc alloy designation or a magnesium alloy designation. The certificate should reference the same grade. If the drawing calls for a specific magnesium alloy with a particular manganese and nickel content, the certificate must show that the heat meets that specification.

A common mistake is a supplier providing a certificate for a higher grade alloy than required. For example, a drawing may call for a standard zinc alloy, but the supplier provides a certificate for a premium grade with higher copper content. This is not a defect, but it is a deviation from the specification. The buyer should confirm whether the higher grade is acceptable. If the specification is strict, the part should be held until a corrected certificate is provided.

For magnesium, the deviation risk is higher. A drawing may call for a structural grade with controlled corrosion resistance. If the supplier provides a certificate for a different grade with higher iron content, the corrosion behavior may change. The buyer should not accept the part without a formal deviation review.

Checklist for drawing alignment:

  1. Confirm the alloy designation on the certificate matches the drawing.
  2. Verify the specified chemical ranges on the drawing are met by the measured values on the certificate.
  3. Check that the certificate references the correct alloy standard or specification.
  4. Confirm the certificate is issued for the correct part number and revision.

A red flag is a certificate that references an old revision of the drawing. If the drawing has been changed and the alloy specification was updated, the certificate must reflect the new revision. A certificate that matches the old revision is not valid for the current part.

Review heat analysis and retest results

Some alloy certificates include a separate heat analysis or retest result. This is a second verification of the chemical composition. For zinc, this may be a lab test performed on a sample from the melt. For magnesium, it may be a test performed on an ingot or extrusion. The heat analysis should be included in the certificate package or provided as a separate document.

  • Confirm the heat analysis date is on or before the date of the alloy certificate.
  • Check that the heat analysis values match the values on the alloy certificate.
  • Verify the lab or test method is named on the document.
  • Confirm the sample size and method are described, if available.

A red flag is a heat analysis that does not match the alloy certificate. If the certificate says the aluminum content is 0.5 percent, but the heat analysis shows 0.7 percent, the discrepancy must be resolved. Do not release the part until the foundry explains the difference.

Another red flag is a heat analysis performed after the part has already been shipped. This is not a valid verification step for incoming quality. The heat analysis should be part of the release documentation before the part leaves the foundry. If the buyer discovers a heat analysis after shipment, treat it as a corrective action trigger.

Store and audit the certificate package

The final step is to store the certificate package in a way that supports future audits. The package should include the alloy certificate, mill test report, heat analysis, and any deviation approvals. Store these documents in a system that links them to the part number, lot number, and heat number. This makes it possible to retrieve the documents if a quality issue arises in the field.

  • File the certificate package by part number and lot number.
  • Link the heat number to the receiving inspection report.
  • Store the documents in a format that is accessible to the quality team.
  • Review the certificate package during supplier audits.

A red flag is a certificate package that is stored in a physical folder without a digital index. If the part is out of service and a quality issue is discovered, the buyer needs to retrieve the certificate quickly. A physical folder that is lost or misfiled is a significant risk.

Another red flag is a supplier that provides certificates only after a request. While it is acceptable to request documents, the supplier should provide them as part of the standard shipment package. If the buyer has to follow up to obtain the certificate, the supplier’s quality system is weaker than it should be.

Red flags that should trigger a hold

The following items should trigger an immediate hold on the incoming material:

  • The heat number on the alloy certificate does not match the heat number on the mill test report.
  • The chemical analysis values are outside the specified alloy range.
  • The certificate is unsigned or lacks a valid company stamp.
  • The certificate references an old revision of the drawing.
  • The heat analysis date is after the date of shipment.
  • The certificate package is incomplete, with missing documents or missing heat numbers.

A hold is not a rejection. It is a pause that gives the quality team time to resolve the issue. The buyer should document the hold, notify the supplier, and request a corrective action plan. If the issue is minor, such as a missing stamp, the supplier may correct the document. If the issue is major, such as a chemical out of tolerance, the part should be quarantined and returned.

By following this checklist, a buyer can verify that incoming zinc and magnesium die castings meet the specified alloy composition and quality standards. The checklist is a practical audit tool that can be used during receiving inspections, supplier scorecards, and internal quality reviews. It reduces the risk of accepting material that does not meet the design intent.